Cable model for high speed data transmission

Looking at cable models, an interesting expression was found. Though approximate and using ” typical cable parameters” it can be used to at least get a feel for the challenges of transmitting high speed data down a UTP cable. The expression is: f3db = 2.25E4/(d*d). Here d is the length of the cable in Km. From this an interesting conclusion can be drawn. The bandwidth of this “typical” cable of length 100 Meters is only 2.25 Mhz. At the other extreme, a 1 Meter cable will have a 22.5 GHz of bandwidth. A 10 Meter cable will have a bandwidth of 225 Mhz and so on. So if we need to transmit data at high MHz or low GHz speeds, on a longer cable, then there is no option except to design and use an equalizer. This is of course a whole new ball game with many issues. From an initial assessment it appears that an analog equalizer is the best option here. The design is understandable and the technology is available to implement it in a reasonable amount of cost, time and space on an ASIC as needed.

LNA

SPG designs, develops and delivers custom analog and RF/wireless asics and modules.

FPGA Design and development service

Contact SPG using phone: 602-626-0272 for fast service.

A wideand RF detector ( 40 Mhz to 3 Ghz) -75 dBm to 5 dBm input

A wideband RF detector

A wideband RF detector

Linear detector performance

Linear detector performance curves

A wideband linear RF detector

Price for one unit: $25.00. Lead time for delivery 3 days. 30 Day return policy. Pricing for 100 units or more: $20.00 per unit.  Please contact Signal Processing Group Inc. for details for purchase from Signal Processing Group Inc. Email: spg@signalpro.biz 24/7

Wideband RF detector perforamce , more details

Contact Signal Processing Group Inc.

Please contact Signal Processing Group Inc. on email: spg@signalpro.biz . We will answer within 24 hours.

2 stage 35 dB gain RF amplifier. Front of the module

Full range frequency response

2 stage amplifier deta

Please see details at http://www.signalpro.biz/2rf_amplifier_details.htm    Delivery lead time is 3 days. Return within 30 days for a full refund. Price is $15.00 for one unit and $10.00 per unit in volumes of 100. For higher volumes than 100 please contact Signal Processing group Inc.

miniature LNA module

Mni LNA performance

Delivery lead time is 3 days. Return within 30 days for a full refund. Price is $15.00 for one unit and $12.00 per unit in volumes of 100. For higher volumes than 100 please contact Signal Processing Group Inc. at email: spg@signalpro.biz or call 602-626-0272 for fastest service.

A high frequency divider from 500 Mhz to % Ghz+

The input interface.
The frequency divider has a differential analog interface. The following parameters apply:
The minimum frequency that can be input is 500 Mhz and the maximum frequency is 6.0 Ghz.
The RF input level is 5 dBm to – 5 dBm. For lower frequencies make sure that the slew rate is
greater than 560 V/us. The input is biased by two 500 Ohm resistors connected to a 1.6V DC bias.
Therefore AC coupling is used at the input. These are two 100pF capacitors.
The output interface.
The output is single ended. The output driver is capable of sourcing and sinking 24 mA. The
equivalent output impedance is 50 Ohm. To avoid reflections it is recommended that the divider
work into a 50 Ohm load.
General operation.
The inputs are applied to the input SMA I/O. The product will work with both a differential input as
well as a single ended input. However, a differential input works best. The division ratio is applied
to the N1 and N2 control inputs as follows:
N2 N1 Division ratio
0 0 8
0 1 16
1 0 32
1 1 64
The logic levels are:
Logic level Voltage
1 1.4V minimum
0 0.6V maximum
The supply voltage interface.
The operating supply voltage is 3.3V typical. The quiescent (DC) operating supply current is 2 mA.

A high frequency divider 500 Mhz to 5 Ghz+

Contact Signal Processing Group Inc for details and acquisition

Please contact Signal Processing Group Inc. at email: spg@signalpro.biz or telephone 602-626-0272. Get a response within minutes or worst case 24 hours if contact is by email.

SPDT DC to 3 Ghz RF switch

DC to 3 Ghz RF SPDT switch

RF Switch typical features

Supply voltage = Vcc = 0/+5 Vdc
Operatng temperature = TA = -50° C to 125 Deg C
Operating impedance = 50 Ohm
Input power for 1 dB
compression ( 5.0V system) = 37 dBm ( f = 0.5 to 3 Ghz)
Input third order Intercept = 64 dBm ( 0 to 5.0V system, f = 0.5 to 3 Ghz)
Operating frequency range = DC to 3 Ghz.
Insertion loss DC to 3 Ghz = 0.8 dB
Isolation DC to 3 Ghz = 14 dB minimum
Return loss DC to 3 Ghz = 20 dB
50% contl to 10/90 %
( ON/OFF) = 120 ns

A single stage RF amplifier as a gain block

A single stage RF amplifier summary specifications

Summary Specifications

Gain,  Operating: 19.5 dB
Operating frequency range: 1.0 – 2700 Mhz
OIP3: (Pout = 19.0 dBm),  -8.5 dBm
P1dB: 4.6 dBm
N.F: 4.2 dB
Supply voltage Operating: 3.3  – 5.5 Volts

Price: single unit $7.50, 100 units : $5:50.

Free delivery, shipping lead time 2 days.

30 day return policy, buyer ships.
Supply current Supply = 5.0V,  23.0 mA

Leave a Reply