Decimation filters for Sigma – Delta A/Ds

A typical filter used as the pre-decimation filter for an oversampled A/D is the Hogenauer filter, also called the CIC filter. These filters have some advantages which make them particularly suitable for use as decimation filters. In general the output stream from a OSR A/D is a 1 bit high frequency digital signal. The 1 bit signal has to be downconverted in frequency and increased in bit width. This is the fundamental decimation operation. Hogenauer filters offer the following advantages (1) No multipliers are needed. (2) No storage is needed for filter coefficients. (3)Intermediate storage is reduced by integrating at the high sampling rate and comb filtering at a low rate. (4) The structure of the CIC filters is very uniform, using only two basic building blocks. (5) Little external control or complicated local timing is required. (6) The same design can easily be used for a wide range of rate change factors with the addition of a scaling unit. As a result of these advantages Hogenauer filters have been used and continue to be used in overampled systems. A technical report prepared by technical staff at Signal Processing Group Inc. is now available in a series of posts that deal with the Hogenauer filter as well as OSR A/D converters. It was assumed that since the CIC filter is an important component at the backend of an OSR ADC, understanding the design parameters of this filter is essential to the design of the overall OSR ADC. Subsequent posts to this one deal with the details of design for decimation filters. The paper may be found at http://www.signalpro.biz>engineer’s corner.

LNA

SPG designs, develops and delivers custom analog and RF/wireless asics and modules.

FPGA Design and development service

Contact SPG using phone: 602-626-0272 for fast service.

A wideand RF detector ( 40 Mhz to 3 Ghz) -75 dBm to 5 dBm input

A wideband RF detector

A wideband RF detector

Linear detector performance

Linear detector performance curves

A wideband linear RF detector

Price for one unit: $25.00. Lead time for delivery 3 days. 30 Day return policy. Pricing for 100 units or more: $20.00 per unit.  Please contact Signal Processing Group Inc. for details for purchase from Signal Processing Group Inc. Email: spg@signalpro.biz 24/7

Wideband RF detector perforamce , more details

Contact Signal Processing Group Inc.

Please contact Signal Processing Group Inc. on email: spg@signalpro.biz . We will answer within 24 hours.

2 stage 35 dB gain RF amplifier. Front of the module

Full range frequency response

2 stage amplifier deta

Please see details at http://www.signalpro.biz/2rf_amplifier_details.htm    Delivery lead time is 3 days. Return within 30 days for a full refund. Price is $15.00 for one unit and $10.00 per unit in volumes of 100. For higher volumes than 100 please contact Signal Processing group Inc.

miniature LNA module

Mni LNA performance

Delivery lead time is 3 days. Return within 30 days for a full refund. Price is $15.00 for one unit and $12.00 per unit in volumes of 100. For higher volumes than 100 please contact Signal Processing Group Inc. at email: spg@signalpro.biz or call 602-626-0272 for fastest service.

A high frequency divider from 500 Mhz to % Ghz+

The input interface.
The frequency divider has a differential analog interface. The following parameters apply:
The minimum frequency that can be input is 500 Mhz and the maximum frequency is 6.0 Ghz.
The RF input level is 5 dBm to – 5 dBm. For lower frequencies make sure that the slew rate is
greater than 560 V/us. The input is biased by two 500 Ohm resistors connected to a 1.6V DC bias.
Therefore AC coupling is used at the input. These are two 100pF capacitors.
The output interface.
The output is single ended. The output driver is capable of sourcing and sinking 24 mA. The
equivalent output impedance is 50 Ohm. To avoid reflections it is recommended that the divider
work into a 50 Ohm load.
General operation.
The inputs are applied to the input SMA I/O. The product will work with both a differential input as
well as a single ended input. However, a differential input works best. The division ratio is applied
to the N1 and N2 control inputs as follows:
N2 N1 Division ratio
0 0 8
0 1 16
1 0 32
1 1 64
The logic levels are:
Logic level Voltage
1 1.4V minimum
0 0.6V maximum
The supply voltage interface.
The operating supply voltage is 3.3V typical. The quiescent (DC) operating supply current is 2 mA.

A high frequency divider 500 Mhz to 5 Ghz+

Contact Signal Processing Group Inc for details and acquisition

Please contact Signal Processing Group Inc. at email: spg@signalpro.biz or telephone 602-626-0272. Get a response within minutes or worst case 24 hours if contact is by email.

SPDT DC to 3 Ghz RF switch

DC to 3 Ghz RF SPDT switch

RF Switch typical features

Supply voltage = Vcc = 0/+5 Vdc
Operatng temperature = TA = -50° C to 125 Deg C
Operating impedance = 50 Ohm
Input power for 1 dB
compression ( 5.0V system) = 37 dBm ( f = 0.5 to 3 Ghz)
Input third order Intercept = 64 dBm ( 0 to 5.0V system, f = 0.5 to 3 Ghz)
Operating frequency range = DC to 3 Ghz.
Insertion loss DC to 3 Ghz = 0.8 dB
Isolation DC to 3 Ghz = 14 dB minimum
Return loss DC to 3 Ghz = 20 dB
50% contl to 10/90 %
( ON/OFF) = 120 ns

A single stage RF amplifier as a gain block

A single stage RF amplifier summary specifications

Summary Specifications

Gain,  Operating: 19.5 dB
Operating frequency range: 1.0 – 2700 Mhz
OIP3: (Pout = 19.0 dBm),  -8.5 dBm
P1dB: 4.6 dBm
N.F: 4.2 dB
Supply voltage Operating: 3.3  – 5.5 Volts

Price: single unit $7.50, 100 units : $5:50.

Free delivery, shipping lead time 2 days.

30 day return policy, buyer ships.
Supply current Supply = 5.0V,  23.0 mA

Leave a Reply